High-heat underlayment
The deck is covered in underlayment made for metal as a second layer of protection.
Metal Roofing
Metal Roof Installation Elmwood Park, NJ
A Elmwood Park roofer can help you choose between standing seam, ribbed panels and metal shingles and install the full system, with high-temperature underlayment, matched trim and closures at every edge. Dial (551) 367-0165 to talk with a local roofer about a metal roof.
The first choice in any metal roof installation is the panel system. Exposed fastener panels, such as corrugated and ribbed panels, are screwed through the face and go on quickly, but every screw has a washer that will need attention someday. Standing seam panels hide their clips under raised seams, so nothing pierces the flat of the panel and the metal can expand and contract freely.
Next comes the metal itself and the paint on it. Steel with a zinc or aluminum-zinc coating is the standard, while aluminum avoids rust in salty air. PVDF finishes resist fading better than SMP finishes, and gauge, where a lower number means thicker metal, affects dent resistance.
What goes under the metal is easy to overlook and important to get right. Panels normally go over solid sheathing and a heat-rated underlayment, with an ice barrier in the eaves and valleys. Open purlin framing works on outbuildings, while homes are better served by a full deck.
Metal Roof Installation is often paired with standing seam metal roof and metal roof replacement, depending on the cause.
Dealing with this in Elmwood Park, NJ right now? Call (551) 367-0165 to talk to a local roofer.
Call nowThe process
How metal roof installation works
Here is the usual order for a new metal roof.
Choose the system
After choosing standing seam, ribbed panels or metal shingles, the roof is measured to order panels and trim. Accurate measurements mean fewer end laps.
Prepare the deck
The deck is stripped, repaired and checked for flatness, since metal panels show every dip. Flat decking also helps prevent oil canning.
High-heat underlayment
High-temperature synthetic underlayment covers the deck, with ice and water shield at the eaves and valleys where required. This layer is the backup if water ever gets past the metal.
Set the trim
Edge trim at the eaves and valley metal are installed before the panels. Rake trim and ridge cap come later and overlap the panels.
Run the panels
Standing seam panels are clipped and seamed, while exposed fastener panels are screwed through the flat or the rib as the profile requires. Metal filings are swept off right away so they do not rust stain the finish.
Finish the details
Ridge cap goes on over foam or vented closures, sidewalls and chimneys get flashing, and pipes get flexible metal roof boots. Snow guards are often added above doors and walkways so snow does not slide off all at once.
What is included
What a metal roof installation includes
Custom flashing
All trim in matching color and metal for a clean, finished look.
Snow guards
Snow guards and flexible pipe boots are added where needed so nothing is left to improvised sealant.
Ridge ventilation
Closures fill the gaps under the trim while keeping out rain and pests.
Panel selection
A panel system matched to the roof pitch chosen to fit the house and budget.
Related service
Metal Roofing Contractor Elmwood Park, NJ
A metal roofing contractor needs different tools and skills than a shingle crew, from panel benders and seamers to trim brakes for custom flashing. It is fair to ask about the panels they prefer, the gauge they recommend and how they flash chimneys and walls.
For Elmwood Park homeowners, the right metal roofing contractor will show how each system handles your roof shape. Ask to see a few local roofs they have done, and look at how straight the panels run and how the trim meets the walls.
Related service
Stone Coated Steel Roof Elmwood Park, NJ
Stone coated steel is formed steel topped with granules so it resembles tile, shake or dimensional shingles. It handles hail and wind well, weighs a fraction of tile and has a quieter surface than bare metal.
The panels often hang on wood battens, which lift them off the deck for airflow. For Elmwood Park homes that want a tile or shake look without the weight, it is a strong option.
Related service
Metal Shingle Roof Elmwood Park, NJ
Metal shingles are individual interlocking panels shaped like traditional roofing units. Hidden fasteners and small units make them a good fit for roofs with dormers and valleys.
For Elmwood Park homeowners who want metal without the look of panels, metal shingles are a common choice. Installation details like starter, valleys and ridge are specific to each product line.
Local help
Metal Roof Installation Near Me
Metal roofs are going on more Elmwood Park homes every year, alongside the shops and barns that have used metal for generations. Older buildings in Elmwood Park and nearby towns like Garfield, Fair Lawn, Paterson and Lodi often have exposed fastener panels, while newer homes lean toward standing seam or metal shingles, and a roofer who installs metal regularly will know which system fits each kind of building.
For metal roof installation in Elmwood Park, NJ or nearby towns like Garfield, Fair Lawn, Paterson and Lodi, call (551) 367-0165 to reach a roofer who covers your street.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Elmwood Park is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
Small roof problems caught early usually stay small repairs.
Local knowledge
Roofers in Elmwood Park know the roof types and weather wear common in local homes.
Clear next steps
Ask the roofer about the cause, the options and the estimate before work starts.
Metal Roof Installation questions
Should I choose standing seam or exposed fastener metal roofing?
The difference is in how the panels are held down. Exposed fastener panels are screwed through the flat or rib, and standing seam uses concealed clips with raised seams. Many homeowners choose standing seam for houses and exposed fastener for barns and shops.
Does metal roof thickness matter?
Thickness is measured in gauge, and 24 is thicker than 26 or 29. Most homes use 24 or 26 gauge steel, while 29 gauge is common on outbuildings. The right gauge depends on the panel and the weather it faces.
Does a metal roof attract lightning?
Lightning is drawn by height and location, not by roofing material. Strikes depend on height, terrain and nearby objects, and a metal roof is no more likely to be hit than any other roof. If a strike happens, metal will not catch fire like some roofing can.
How long does a metal roof last?
A well installed steel roof commonly lasts forty years or more. Standing seam with a quality PVDF finish tends to last longest, while exposed fastener roofs need new screws along the way. Salt air, scratches and poor installation shorten that life.
How noisy is a metal roof?
Over a solid deck with underlayment and an insulated attic, rain on metal sounds much like rain on shingles. Metal over open framing, like a barn, is the noisy version. Stone coated steel and metal shingles are among the quietest options.
More questions? Call (551) 367-0165
Often needed together
Standing Seam Metal Roof
Long-lasting standing seam roofs, from snap-lock to mechanically seamed panels, for homes, additions and low slope roofs.
Learn moreMetal Roof Replacement
Tearing off failed metal panels, repairing the framing and putting on a new metal roof, chosen to fit the building and the old roof underneath.
Learn moreRoof Installation
Putting on a new roof the way the material maker intends, whether it is asphalt shingles, metal or another material.
Learn moreCommercial Metal Roofing
Commercial metal roofing from structural standing seam to exposed fastener panels, plus retrofits over old roofs, with clips, fasteners and trim matched to the panel system.
Learn more
Looking for something else?
See all roofing servicesTalk to an Elmwood Park roofer about metal roof installation
Call (551) 367-0165 to talk to a roofer serving Elmwood Park, NJ.